The Global Exhaust Gas Recirculation Cooler Market size in the report has been segmented into type, application, and region. The types of exhaust gas recirculation coolers are plate wing, shell, and tube. Applications of these products are automotive applications and aerospace applications. Regions covered in this study are North America, Latin America, Europe, Asia Pacific (APAC), and Middle East & Africa (MEA).
An exhaust gas recirculation cooler is a device that decreases the temperature of hot engine gases during internal combustion by increasing their contact with cool ambient air. The exhaust gas recirculations are thus cooled down before they enter into the atmosphere, providing an ecological and economical solution. This technology reduces CO emissions without any additional cost or fuel consumption in comparison to conventional engines.
The exhaust gas recirculation cooler, which is also called an "EGR," functions by recycling some of the exiting gases back into the combustion chamber to be used again as fuel or coolant before being released to the atmosphere. In automotive applications, EGR coolers help maintain engine temperatures by recycling waste gasses back into the combustion chamber so they can be used again as fuel or coolant before being released into the atmosphere.
On the basis of Type, the global exhaust gas recirculation cooler market is segmented into Plate Wing, Shell, Tube.
The plate-wing type of exhaust gas recirculation cooler is an installation that consists of a series of plates, where the gases are cooled by air circulation. The high-temperature hot engine gases flow through narrow channels and then cool down due to contact with cold ambient air blown over them at low velocity. In this case, there is not so much heat transfer between two fluids as well as fresh atmospheric air does not have enough time to mix with the discharged gases before they enter into the atmosphere. Moreover, these systems use higher pressure than shell or tube collectors. As a result, cooling efficiency decreases but it has lower mass inertia which allows better control on vehicle speed fluctuations (e.g., acceleration). This device can be used for both high and low-speed vehicles (e.g., trucks and motorcycles).
Shell type exhaust gas recirculation cooler is a device that cools the engine gases. It operates in such a way: hot discharged gases are directed into an expansion chamber which expands them at low velocity. The colder air from outside enters mixes with and cools down these gases before they enter back to the engine through a bypass duct where it can finally mix with fresh atmospheric air coming directly from outside of the vehicle. This system has higher pressure than plate or tube collectors but lower mass inertia and better control on fluctuations (e.g., acceleration) of vehicle speed due to its ability to operate for both high and low speeds vehicles like trucks, motorcycles, etc. It also provides cooling efficiency without increasing weight as well as external surface area contact so there is no need for large cooling fins.
The tube type of exhaust gas recirculation cooler is a cylindrical device that is attached to the top of an automobile's engine. It allows for some air from inside the car to pass through it via channels on either side where it can mix with hot and toxic gases coming out of the car’s exhaust system. This cooled, mixed air then re-enters into the vehicle so that passengers may breathe it in while driving as opposed to polluted outside air which could potentially do harm or even kill them. These tubes are generally made up of steel sheets welded together and their shape helps prevent heat transfer by not allowing any direct contact between two different surfaces during operation. They also have fins that are bent to create a large surface area which aids in heat transfer.
On the basis of Application, the global exhaust gas recirculation cooler market is segmented into Car, Aerospace.
Car- Exhaust gas recirculation cooler is a device to reduce the engine’s intake temperature. It has two main parts: an exhaust flow mixer and a hot air receiver. The exhaust flow mixer mixes some of the exited gases with fresh incoming air from the car's outside environment, thus reducing heat transfer between these two components and lowering the intake temperature in turn.
In automotive applications, EGR coolers help maintain engine temperatures by recycling waste gasses back into the combustion chamber so they can be used again as fuel or coolant before being released into the atmosphere. Car- Exhaust gas recirculation cooler makes use of a simple but clever design: Wastes from car engines are recycled and reused in order for them not to go out with release through tailpipe emissions.
The application of an exhaust gas recirculation cooler in aerospace is minimizing the risks by reducing heat transfer between these two components and lowering the intake temperature. This allows for a more efficient engine, which contributes positively to fuel efficiency on airplanes.
On the basis of Region, the global exhaust gas recirculation cooler market is segmented into North America, Latin America, Europe, Asia Pacific, and Middle East & Africa (MEA). In terms of revenue contribution in 2028; the USA will be on top followed by China and then Japan. However owing to a rise in demand from other emerging economies like India, Brazil among others there exists the potential for growth in these regions as well.
North America, the largest market for exhaust gas recirculation coolers is likely to grow at a CAGR of about 12% during 2020-2028. The region’s presence in this segment can be attributed to factors such as high demand from the automotive industry and increased penetration of technology within the residential sector which leads to rising in cooling load.
* Growing emission regulation norms and strict environmental regulations are expected to drive the global exhaust gas recirculation cooler market.
* Rising demand for fuel efficiency, low cost of operation in car engines is projected to increase the growth rate of this market during the forecast period.
* Increasing use of electronic power steering systems for automobiles is also an important factor driving the growth of this market over 2028-2037.
*Younger generation's preference towards SUVs & CUVs owing to their spacious interior will have a positive impact on this industry as these vehicles require cooling systems more frequently than other types of cars which will result in increased penetration rates during 2021-2027 across various regions.
Up Market Research published a new report titled “Exhaust Gas Recirculation Cooler Sales Market research report which is segmented by Types (Plate Wing, Shell And Tube), By Applications (Car, Aerospace), By Players/Companies Kelvion Holding, Modine Manufacturing Company, Tokyo Roki Co Ltd, BorgWarner, Bühler Group, Valeo, Tantivy Automotive Co Ltd, Emitec GmbH, bdp Mechanical Components, Rheinmetall Automotive AG”. As per the study the market is expected to grow at a CAGR of XX% in the forecast period.
Report Attributes | Report Details |
Report Title | Exhaust Gas Recirculation Cooler Sales Market Research Report |
By Type | Plate Wing, Shell And Tube |
By Application | Car, Aerospace |
By Companies | Kelvion Holding, Modine Manufacturing Company, Tokyo Roki Co Ltd, BorgWarner, Bühler Group, Valeo, Tantivy Automotive Co Ltd, Emitec GmbH, bdp Mechanical Components, Rheinmetall Automotive AG |
Regions Covered | North America, Europe, APAC, Latin America, MEA |
Base Year | 2020 |
Historical Year | 2018 to 2019 (Data from 2010 can be provided as per availability) |
Forecast Year | 2028 |
Number of Pages | 238 |
Number of Tables & Figures | 167 |
Customization Available | Yes, the report can be customized as per your need. |
The report covers comprehensive data on emerging trends, market drivers, growth opportunities, and restraints that can change the market dynamics of the industry. It provides an in-depth analysis of the market segments which include products, applications, and competitor analysis.
The market is segmented by Type Plate Wing, Shell And Tube and By Application Car, Aerospace.
Some of the companies that are profiled in this report are:
Exhaust Gas Recirculation Cooler Sales Market research report delivers a close watch on leading competitors with strategic analysis, micro and macro market trend and scenarios, pricing analysis and a holistic overview of the market situations in the forecast period. It is a professional and a detailed report focusing on primary and secondary drivers, market share, leading segments and geographical analysis. Further, key players, major collaborations, merger & acquisitions along with trending innovation and business policies are reviewed in the report.
Key Benefits for Industry Participants & Stakeholders:
Based on region, the market is segmented into North America, Europe, Asia Pacific, Latin America and Middle East & Africa (MEA). North America region is further bifurcated into countries such as U.S., and Canada. The Europe region is further categorized into U.K., France, Germany, Italy, Spain, Russia, and Rest of Europe. Asia Pacific is further segmented into China, Japan, South Korea, India, Australia, South East Asia, and Rest of Asia Pacific. Latin America region is further segmented into Brazil, Mexico, and Rest of Latin America, and the MEA region is further divided into GCC, Turkey, South Africa, and Rest of MEA.
We have studied the Exhaust Gas Recirculation Cooler Sales Market in 360 degrees via. both primary & secondary research methodologies. This helped us in building an understanding of the current market dynamics, supply-demand gap, pricing trends, product preferences, consumer patterns & so on. The findings were further validated through primary research with industry experts & opinion leaders across countries. The data is further compiled & validated through various market estimation & data validation methodologies. Further, we also have our in-house data forecasting model to predict market growth up to 2028.
How you may use our products:
Reasons to Purchase the Exhaust Gas Recirculation Cooler Sales Market Report:
Some other reports from this category!